SSA3000X-R Series Firmware Update
Version:
V3.2.2.6.0R7
SSA3000X-R Firmware Update
Version:
V3.2.2.5.1R1
2022-06-28
Release notes
Notice:
This firmware must be upgraded from V3.2.2.4.0 or later. If your analyzer has an earlier version, please update to V3.2.2.4.0 first and then proceed to update to the latest version.
Improvements:
•[:SENSe]:ADEMod:FM:DEVI?
•[:SENSe]:ADEMod:FM:DRIFt?
•[:SENSe]:BWIDth[:RESolution]
•[:SENSe]:BWIDth[:RESolution]?
•[:SENSe]:BWIDth:EQLPf
•[:SENSe]:BWIDth:EQLPf?
•CALCulate:MARKer#:PTPeak
Solved Issues:
This firmware must be upgraded from V3.2.2.4.0 or later. If your analyzer has an earlier version, please update to V3.2.2.4.0 first and then proceed to update to the latest version.
Improvements:
- Optimize the Ref level and Att couple
- Add SCPI commands in MA Mode
•[:SENSe]:ADEMod:FM:DEVI?
•[:SENSe]:ADEMod:FM:DRIFt?
•[:SENSe]:BWIDth[:RESolution]
•[:SENSe]:BWIDth[:RESolution]?
•[:SENSe]:BWIDth:EQLPf
•[:SENSe]:BWIDth:EQLPf?
•CALCulate:MARKer#:PTPeak
- Add Cable Atten to correct cable loss in DTF Mode
- Add .trc file in EMI Mode
- Add .lic file auto scan
Solved Issues:
- Fix the false signals in density view in RTSA mode
- Fix pi/4 DPSK和pi/8 DPSK decode errors in MA mode
- Fix calibration error when port extension on in VNA mode
- Fix fft frequency error in narrow span in SA mode
- Fix trace avg calculation error in SA mode
- Fix the zero sweep type when fft in SA mode
SSA3000X-R Firmware Update
Version:
V3.2.2.5.0
2021-12-08
Release notes
Notice:
This firmware must be upgraded from V3.2.2.4.0 or later. If your analyzer has an earlier version, please update to V3.2.2.4.0 first and then proceed to update to the latest version.
New Functionality:
Improvements:
Solved Issues:
Fixed center Freq error;
Fixed limit fail to stop error;
Fixed auto frequency error;
Fixed in normalization, auto re-normalized after any setting changes
Fixed STA file saving error;
Fixed CSA file loading error;
Fixed S21 calibration error;
Fixed enhanced calibration error
Fixed Freq step error
Fixed saving std lim path error
This firmware must be upgraded from V3.2.2.4.0 or later. If your analyzer has an earlier version, please update to V3.2.2.4.0 first and then proceed to update to the latest version.
New Functionality:
- Add Ext Trigger Delay from 0-10 seconds in SA Mode
- Add Limit in Log mag and Lin mag format; add calibration average; add s1p touchstone file save in VNA mode
Improvements:
- VNA sweep points up to 10001; Scale down to 0.001 in Smith chart;
- MA Filter type Nyquist change to Raised Cosine to align SCPI command; improve filter performance in low frequency
Solved Issues:
- SA mode:
Fixed center Freq error;
Fixed limit fail to stop error;
Fixed auto frequency error;
Fixed in normalization, auto re-normalized after any setting changes
- VNA mode:
Fixed STA file saving error;
Fixed CSA file loading error;
Fixed S21 calibration error;
Fixed enhanced calibration error
- RTSA mode:
Fixed Freq step error
- EMI mode:
Fixed saving std lim path error
- Web browser: Fixed change IP error, Login error after changing password
SSA3000X-R Firmware Update
Version:
V3.2.2.4.0
2021-01-21
Release notes
- This version can not be rolled back
- Fix TG switch error at small RBW
- Fix Help and Limit file lost when Factory reset
- Fix Auto open delay unit error in VNA mode
- Fix CNR calc error when no peak found
- Fix OBW result overflow
- Fix Harmonic calc error at 100Hz RBW
- Fix Reflection Open+Short calibration action
- Fix spectrum amplitude error in DMA mode
- Optimize EMI .csv file content to all signal list
- Optimize EMI peak search
- Optimize Auto cal process
- Add Peak search to Spectrum in DMA mode
SSA3000X-R Firmware Update
Version:
V3.2.2.3.3R1
2020-12-11
Release notes
New Functionality:
• Add EMI filter in SA for EMI option
Solved Issues:
• Optimize the response in RTSA
• Optimize the TG flatness and control procedure
• Optimize Help
• Fix Correction, .csv file, add peak numbers to 20 in EMI mode
• Fix ADC overload warning error, and time unit error in Calibration in VNA Mode
• Fix amplitude error in DMA Mode
• Fix the frequency band downgrade to 3.2GHz on some units
• Fix upgrade failure issue
• Add EMI filter in SA for EMI option
Solved Issues:
• Optimize the response in RTSA
• Optimize the TG flatness and control procedure
• Optimize Help
• Fix Correction, .csv file, add peak numbers to 20 in EMI mode
• Fix ADC overload warning error, and time unit error in Calibration in VNA Mode
• Fix amplitude error in DMA Mode
• Fix the frequency band downgrade to 3.2GHz on some units
• Fix upgrade failure issue
Release Notes
Release Notes