SDS800X HD Firmware Update
Version：
V1.1.6.5
2025-04-22
Release notes
1. Fixed several bugs
a) Scope wont't boot if set for DHCP and connected to LAN without DHCP server
b) An "Acquiring" progress bar is showing up on 1 ms/div instead of 100ms/div as before
c) Remove BW Limit warning
d) When FFT is set to certain frequency bands, such as 1kHz to 6kHz, meaningless axis labels are displayed (sweep mode is set to logarithmic)
a) Scope wont't boot if set for DHCP and connected to LAN without DHCP server
b) An "Acquiring" progress bar is showing up on 1 ms/div instead of 100ms/div as before
c) Remove BW Limit warning
d) When FFT is set to certain frequency bands, such as 1kHz to 6kHz, meaningless axis labels are displayed (sweep mode is set to logarithmic)
SDS800X HD Firmware Update
Version：
V1.1.6.2
2025-03-12
Release notes
1. Support decode after roll stop
2. Support decode hysteresis
3. Support Blackman-Harris and Gaussian window of FFT
4. Support XY split screen display
5. Support movable channel label
6. Support saving measurement statistics results
7. Remote reading acceleration(SERVICE->WAV ACC)
8. Optimize UI
a）Add confirmation dialog for save To Default Key
b）Remove excess zeros in the axis labels
c）When the horizontal axis labels are too long, they will be displayed alternately up and down
d）Use real "µ" instead of small letter "u".
9. Fixed several bugs
a）When Beep enabled, physical buttons beep only until first move of any encoder
b）When the probe is not 1X and the vertical reference is Offset, the zoom area is unreasonable when changing the vertical scale
c）After NTP synchronization time, the history list time is wrong
d）When the points is ≥10M, FFT has unreasonable spurious signals
2. Support decode hysteresis
3. Support Blackman-Harris and Gaussian window of FFT
4. Support XY split screen display
5. Support movable channel label
6. Support saving measurement statistics results
7. Remote reading acceleration(SERVICE->WAV ACC)
8. Optimize UI
a）Add confirmation dialog for save To Default Key
b）Remove excess zeros in the axis labels
c）When the horizontal axis labels are too long, they will be displayed alternately up and down
d）Use real "µ" instead of small letter "u".
9. Fixed several bugs
a）When Beep enabled, physical buttons beep only until first move of any encoder
b）When the probe is not 1X and the vertical reference is Offset, the zoom area is unreasonable when changing the vertical scale
c）After NTP synchronization time, the history list time is wrong
d）When the points is ≥10M, FFT has unreasonable spurious signals
SDS800X HD Firmware Update
Version：
V1.1.3.8
2024-06-28
Release notes
- Optimize UI, change "on/off" to "On/Off".
- Solve the problem that some numbers from 200-223 cannot be entered in the first byte of the IP address.
- Standard software functions of FG and LA.
SDS800X HD Firmware Update
Version：
V1.1.3.6
2024-05-23
Release notes
- Solve the problem of trigger holdoff fails.
- Solve the problem of CAN decoding causing crashes with a small probability.
- Modify the kernel solve the problem that scpi cannot be used on a computer with keysight driver installed.
- Solve the problem of advanced trigger (Qualified, Nth Edge, Delay, Setup/Hold) parameters are not recalled.
- Solve the problem of delay trigger level setting error.
- Solve the problem of when the edge is set to Alternating, trigger jitter will occur when entering the other trigger type.
- Solve some known problems.
- Optimize waveform capture rate.
- Optimize Self calibration speed.
- Optimize UI.
SDS800X HD Firmware Update
Version：
V1.1.3.3
2024-03-05
Release notes
1. Solve the problem that Bode Plot cannot control sdg1000
2. Solve the problem that user probe coefficient are not restored after reboot
3. Solve the problem that the screen does not support multi-touch
2. Solve the problem that user probe coefficient are not restored after reboot
3. Solve the problem that the screen does not support multi-touch
SLA1016(Optional) Firmware Update
Version：
V8.2.3
2024-03-05
Release notes
1. Support SDS1000X HD and SDS800X HD, 8.2.x is only applicable to SDS1000X HD and SDS800X HD.
Release Notes
Release Notes
