SDG2000X Series Firmware Update
Version：
V2.01.01.37R8
2023-09-08
Release notes
1. Solve the problem of slow USB drive detection during startup
2. Solve the problem of outputting abnormal pulses during burst mode
3. Add instructions for saving and reading status（XML）files
4. Add the instruction to clear the statistics of the counter
2. Solve the problem of outputting abnormal pulses during burst mode
3. Add instructions for saving and reading status（XML）files
4. Add the instruction to clear the statistics of the counter
SDG2000X Firmware Update
Version：
V2.01.01.37R6
2023-04-11
Release notes
1.Compatible with Rev.G hardware
2.Fix the bug that the system does not respond when there is no operation for a long time after the counter is turned on
2.Fix the bug that the system does not respond when there is no operation for a long time after the counter is turned on
SDG2000X Series Firmware Update
Version：
V2.01.01.37R3
2022-12-09
Release notes
- Compatible with Rev.F hardware; if the hardware version is “05-xx-xx-xx-xx”, it will not support to roll back previous firmware version
- Supported trig dual channel separated when use manual trigger.
- Supported using another channel as the modulation source
- Supported setting the output frequency after the completion of sweep
- Counter add fast measurement mode
- Changed the square waveform data used in square FM modulation
SDG800 Series Firmware Update
Version：
V1.08.01.15R2
2022-09-16
Release notes
- Fixed the bug that startup occasional failures
- Fixed the bug of burst sync output exception
- Fixed the bug that may not output when switch the waveform after the burst is turn off
SDG800 Series Firmware Update
Version：
V1.08.01.15
2021-02-04
Release notes
1. Supported to automatically enable the output after power-on: Utility | Output Setup | Power on State
2. Compatible with Rev.E hardware
2. Compatible with Rev.E hardware
SDG2000X Series Firmware Update
Version：
V2.01.01.35R3B2
2019-12-17
SDG2000X Series Firmware Update
Version：
V2.01.01.35R3B1
2019-09-11
SDG800 Series Firmware Update
Version：
V1.08.01.13R9
2019-08-19
SDG2000X Series Firmware Update
Version：
V2.01.01.23R8
2018-09-21
SDG800 Series Firmware Update
Version：
V1.08.01.13R6
2018-08-31
SDG1000X Series Firmware Update
Version：
V1.01.01.33R8
2024-04-18
Release notes
- add the function of long pressing store/recall to save screenshots.
- corrected the amplitude deviation problem of ramp waveform output.
- fixed the problem of error prompt when inserting U disk.
- fixed the problem of sync signal output error in modulation mode.
- corrected the problem of abnormal output of small-amplitude FM signal.
- solve the problem of abnormal output when using external clock.
SDG2000X Series Firmware Update
Version：
V2.01.01.23R7
2017-09-22
SDG800 Series Firmware Update
Version：
V1.08.01.13R5
2018-04-18
SDG1000X Series Firmware Update
Version：
V1.01.01.33R3
2022-04-21
Release notes
Fixed a bug. Resolved occasional startup failures.
SDG2000X Series Firmware Update
Version：
V2.01.01.23R3
2017-03-28
SDG800 Series Firmware Update
Version：
V1.08.01.12R2
2016-06-28
SDG6000X Firmware Update
Version：
V6.01.01.36R8
2023-06-09
SDG1000X Series Firmware Update
Version：
V1.01.01.33R1B6
2020-02-21
Release notes
1. Optimized debounce of the front panel buttons.
SDG2000X Series Firmware Update
Version：
V2.01.01.15R2
2015-10-21
SDG800 Series Firmware Update
Version：
V1.08.01.12R1
2016-03-09
SDG6000X Series Firmware Update
Version：
V6.01.01.36R3
2022-09-01
SDG800 Series Firmware Update
Version：
V1.08.01.11
2015-12-09
SDG1000X Series Firmware Update
Version：
V1.01.01.33R1B5
2019-08-19
SDG800 Series Firmware Update
Version：
V1.08.01.10
2015-09-30
SDG5000 Series Firmware Update
Version：
V5.01.01.15R5
2018-02-03
SDG1000X Series Firmware Update
Version：
V1.01.01.33R1
2019-02-26
SDG6000X Series Firmware Update
Version：
V6.01.01.36
2021-02-05
Release notes
- Allowed one channel to modulate the other
- Supported Burst in TrueArb mode
- Supported Burst Counter in Burst mode so the number of burst trains can be set to > 1 when trigger source = external or manual
- Added an option to let the SDG start with activated outputs
- Added 50 ohm output impedance text in the UI
- Able to remember the digit of a parameter that had been modified
- Fixed several bugs:
- DDS interpolation bug
- Switching on/off output causes random phase deviation between channels in Track mode
- Incorrect square/pulse waveform initialization in some cases
- Unable to store the level settings for noise
- Unable to recognize the command MODE PHASE-LOCKED
- Freezing issue when being written a 20MB long file with the EasyWaveX
- The setting "BANDSET" with Waveform = NOISE leads to inconsistent behavior on the Noise Bandwidth of the output signal; The real-time noise bandwidth on channel 2 is changed if an AM sine modulation is switched on channel 1
- Unable to install the IQ option before 30 trials run out
SDG800 Series Firmware Update
Version：
V1.08.01.09
2015-07-20
SDG1000X Series Firmware Update
Version：
V1.01.01.30R1B2
2019-01-28
SDG5000 Series Firmware Update
Version：
V5.01.01.15R1
2015-11-12
Release notes
1.Optimized PLL configuration
2.Fixed several bugs
a.Enabling Mod on CH2 may disable Burst on CH1
b.Duty cycle error on Square wave with very long period
c.SCPI command cannot adjust the phase difference between two synchronized units
d.Manual trigger cannot trigger both channels simultaneously
2.Fixed several bugs
a.Enabling Mod on CH2 may disable Burst on CH1
b.Duty cycle error on Square wave with very long period
c.SCPI command cannot adjust the phase difference between two synchronized units
d.Manual trigger cannot trigger both channels simultaneously
SDG6000X Series Firmware Update
Version：
V6.01.01.35R5B1
2019-09-18
SDG800 Series Firmware Update
Version：
V1.08.01.08
2015-01-16
SDG5000 Series Firmware Update
Version：
V5.01.01.12
2015-03-10
SDG1000X Series Firmware Update
Version：
V1.01.01.30.R1
2018-07-26
SDG1000 Series Firmware Update
Version：
V1.01.01.39R7
2019-01-29
SDG800 Series Firmware Update
Version：
V1.08.01.07
2019-08-29
SDG5000 Series Firmware Update
Version：
V5.01.01.10
2014-09-26
SDG6000X Series Firmware Update
Version：
V6.01.01.33R2
2019-05-08
Release notes
测试
SDG1000X Series Firmware Update
Version：
V1.01.01.22R5
2017-09-07
SDG1000 Series Firmware Update
Version：
V1.01.01.39R5
2017-12-25
SDG800 Series Firmware Update
Version：
V1.08.01.06
2014-09-30
SDG6000X Series Firmware Update
Version：
V6.01.01.29R10
2018-07-26
SDG1000X Series Firmware Update
Version：
VP22
2016-10-26
SDG1000 Series Firmware Update
Version：
V1.01.01.39R2
2017-06-05
SDG7000A Series Firmware Update
Version：
V1.1.1.31
2023-11-23
Release notes
- Support frequency hopping function
- Built in EasyWaveX supports multi pulse function
- Add the function of erasing user waveform files with one click
- Solve the problem of system unresponsiveness when loading incorrect IQ waveform files
- Solve the problem of occasional loss of locking when using OCXO
- Solve the problem of loading network disk waveform files getting stuck
- Fixed the bug of false alarms for overvoltage
SDG7000A Series Firmware Update
Version：
1.1.1.29R8
2023-03-15
Release notes
- Fixed the bug of pulse output error under specific configuration
- Added amplitude sweep function
- Added the adjustment of channel skew
- Supported multi-file operation in the file manager
- Optimized the storage strategy of waveform data in sequence playback (The digital channel does not support sequence playback)
- The PRBS rate up to 625Mbps
- Fixed the bug of abnormal signal output during waveform switching
SDG2000X Series Firmware Update
Version：
V2.01.01.17R5
2016-01-16
Release Notes
Release Notes
