SDS1202X-E Firmware (2-Channel Models)
Version:
V1.3.27
SDS1xx4X-E Firmware Update
Version:
V6.1.37R10
2023-03-30
Release notes
Revision History
Optimized VGA configuration
Compatibility between Versions
Source Version | Object Version | Compatibility |
---|---|---|
6.1.37R9 | 6.1.37R10 | Yes |
6.1.37R8 | 6.1.31R10 | Yes |
6.1.37R6 | 6.1.37R10 | Yes |
6.1.37R2 | 6.1.37R10 | Yes |
6.1.26 | 6.1.37R10 | Yes |
6.1.25R2 | 6.1.37R10 | Yes |
6.1.25R1 | 6.1.37R10 | Yes |
6.1.20R1 | 6.1.37R10 | Yes |
6.1.20 | 6.1.37R10 | Yes |
6.1.12R1 | 6.1.37R10 | Yes |
6.1.12 | 6.1.37R10 | Yes |
6.1.33 | 6.1.37R10 | Yes |
6.1.35R2 | 6.1.37R10 | Yes |
Compatibility with SLA1016
Source Version | Object Version | Compatibility |
---|---|---|
8.1.16 | 6.1.33/6.1.37R10 | Yes |
8.1.11 | 6.1.33/6.1.37R10 | No |
8.1.9 | 6.1.33/6.1.37R10 | No |
8.1.8 | 6.1.33/6.1.37R10 | No |
Update instructions
- Important!
- Very important!
- Very important!
SDS1xx4X-E Firmware Update
Version:
V6.1.37R9
SDS1xx4X-E Firmware Update
Version:
V6.1.37R8
SDS1xx4X-E Firmware Update
Version:
V6.1.37R6
SDS1xx4X-E Firmware Update
Version:
V6.1.37R2
2021-08-24
Release notes
- Added data logger featuring Sample and Measurement Logger functions
- Added counter function
- Added Labels
- Added NTP (Network Time Protocol) and Time Zone. Also requires OS update to SDS1xx4X-E_OSV2 which is located on the SIGLENT product webpage. The OS Update Instructions is also included SDS1xx4X-E_OSV2.zip
- Modified negative or positive of horizontal delay: Time zero is in trigger. Before trigger, time position is -time (negative delay relative to trigger) and after trigger is +time (positive delay relative to trigger)
- Fixed a bug with Bin2CSV for ROLL mode
- Rebuilt Bin2CSV to File Converter which can also convert data logger file to CSV.
- Fixed a bug: some case there is a blue line on decode bus
- Fixed a bug with saving hex MSO CSV file
- Fixed a bug: After rebooting , Bode Plot cursor can’t be moved
- Fixed a bug: fine adjusting with customer probe
- WiFi supported Spaces and Special Characters
SDS1xx4X-E Firmware Update
Version:
V6.1.35R2
2020-03-07
Release notes
1. Added support for the SAG1021I USB Isolated AWG Module Hardware
2. Fixed the bug: Sometimes PNSU command returns invalid value (Need referring to the latest Program Guide)
3. Added 9 data bits for UART decoding
4. Fixed the bug of UART decoder with some special settings
5. Increased baud rate of UART trigger from 5 Mbps to 20 Mbps
6. Fixed the bug: The command ‘WF? DAT2’returns error length of waveform when digital is enable
7. Fixed the bug: CSV file of waveform has no indication of the trigger point in the data
8. Fixed the bug: After repowering all FFT markers are on just one peak
9. Fixed the bug: After repowering, signal level of CAN trigger can't be recalled
10. Fixed a few SCPI Commands errors:
MATH: CURSOR_VALUE?
C3:INVERT_SET? is missing
HISTORY_LIST? is missing
DIGITAL:LOW8_SWICHT, typo in name
C5:COUPLING? typo in name
11. Fixed the Bode Plot bug: Sometime there isn't enough delay after the scope switches timebase values before it tries to take a measurement
12. Fixed the bug: Matlab can’t import 14 M Matlab waveform files
13. Fixed the bug:‘WF?’command ignores the length set by ‘WFSU’ for digital
2. Fixed the bug: Sometimes PNSU command returns invalid value (Need referring to the latest Program Guide)
3. Added 9 data bits for UART decoding
4. Fixed the bug of UART decoder with some special settings
5. Increased baud rate of UART trigger from 5 Mbps to 20 Mbps
6. Fixed the bug: The command ‘WF? DAT2’returns error length of waveform when digital is enable
7. Fixed the bug: CSV file of waveform has no indication of the trigger point in the data
8. Fixed the bug: After repowering all FFT markers are on just one peak
9. Fixed the bug: After repowering, signal level of CAN trigger can't be recalled
10. Fixed a few SCPI Commands errors:
MATH: CURSOR_VALUE?
C3:INVERT_SET? is missing
HISTORY_LIST? is missing
DIGITAL:LOW8_SWICHT, typo in name
C5:COUPLING? typo in name
11. Fixed the Bode Plot bug: Sometime there isn't enough delay after the scope switches timebase values before it tries to take a measurement
12. Fixed the bug: Matlab can’t import 14 M Matlab waveform files
13. Fixed the bug:‘WF?’command ignores the length set by ‘WFSU’ for digital
SDS1202X-E Firmware (2-Channel Models)
Version:
V1.3.26
SLA1016 Firmware (Optional For 4-Channel)
Version:
V8.1.16
SDS1xx4X-E Firmware Update
Version:
V6.1.33
SLA1016(Optional) Firmware Update
Version:
V8.1.11
SDS5000X Series Firmware Update
Version:
V0.9.9R3
2024-04-29
Release notes
CAUTION: This release cannot be downgraded to previous releases.
- Compatible with new hardware
- Supported new probes: SCP5030A/SCP5150/SCP5500, SAP5000D
- Trigger: modified the trigger strategy of /AND and OR trigger from FALSE-to-TRUE to TRUE-to-FALSE
- Acquisition: modified the Average strategy in Single mode from acquiring one frame to acquiring averaged X frames (where X = Average count)
- Optimized UI
- Fixed several bugs
- Freezing issue in Roll mode
- Freezing issue relative to Stop-on-Search-Event in Search mode
- In some case the scope does not update the waveform traces after a long time
SDS1xx4X-E Firmware Update
Version:
V6.1.26
SDS5000X Series Firmware Update
Version:
V0.9.8R2
SDS1xx2X-E Firmware Update
Version:
V1.3.23
SDS5000X Series Firmware Update
Version:
V0.9.8R1
2023-06-21
Release notes
1. Increased the data width of saved Average and ERES data from 8-bit to 16-bit
2. Decode: added ARINC429
3. Math: added RBW display for FFT
4. Supported 12-hour time with AM and PM
5. Remote control:
Supported the USB-GPIB adapter
Added command supporting to query average count when Acquisition = Average
Added command supporting to enable/disable axis labels
6. Fixed several bugs
Incorrect prompt when saving .csv with “Save all channels” to a U-disk as specified file name
Channel ON / OFF labels are inconsistent
Freezing issue caused by command CURSor:XDELta?
2. Decode: added ARINC429
3. Math: added RBW display for FFT
4. Supported 12-hour time with AM and PM
5. Remote control:
Supported the USB-GPIB adapter
Added command supporting to query average count when Acquisition = Average
Added command supporting to enable/disable axis labels
6. Fixed several bugs
Incorrect prompt when saving .csv with “Save all channels” to a U-disk as specified file name
Channel ON / OFF labels are inconsistent
Freezing issue caused by command CURSor:XDELta?
SDS2000X Plus Firmware Update
Version:
V1.5.2R3
SDS1xx4X-E Firmware Update
Version:
V6.1.25R2
SDS2000X Plus Series Firmware Update
Version:
V1.5.2R2
SDS5000X Series Firmware Update
Version:
V0.9.7R5
SDS1xx4X-E Operating System(Only For 4-Channel)
Version:
V2
SLA1016 Firmware (Optional For 4-Channel)
Version:
V7.8.1.9
SDS1000CML Series Firmware Update
Version:
V6.01.01.25
SDS2000X Plus Series Firmware Update
Version:
V1.5.2R1
2022-09-16
Release notes
- Measurement enhancement - Added setup/hold time: tsu@R, tsu@F, th@R, th@F
- Optimized UI
- Added SCPI commands for Measure Cursors and clearing measure items in Simple mode
- Supported LXI (only with the Uboot-OS Version 5.4)
- Supported time zone setting
- Fixed several bugs
- Webserver doesn’t show instrument UI if the scope reboot with a wireless mouse connected
- Incorrect “Recall”icon in the File Manager
- Scope freezes with AWG enabled and measure cursor on rise time
- IP setting of AWG in Bode Plot not remembered after reboot
- Network storage only works for SMB1.0
- MEAS:SIMPle:ITEM\sOVSN,ON does not work as expected
- Roll time incorrect at 1ks/div and 20kpts
- Raw data not consistent in x and sinx/x interpolation modes
- Math: Dx parameter of Derivation cannot be increased by universal control
- Incorrect FFT sample rate
SDS5000X Series Firmware Update
Version:
V0.9.7R2
2022-04-27
Release notes
- Acquire: supported Fixed Sample Rate and Fixed Memory Depth modes
- Connectivity:
- Supported LXI
- Supported Network Storage
- Measure: improved the AIM limit from 1,000 to up to 25,000 (AIM limit: the upper limit of horizontal parameters measure statistics in one frame )
- Power Analysis: supported MOSFET SOA (Safe Operating Area)
- Channel:
- Two custom probe ratio options supported
- Supported LeCroy CP030 current probe (with LPA10 adapter)
- UX: Added support for mouse wheel when using a mouse
- Optimized UI
- Remote Control: Supported to read sequence segments by WF command
- Optimized the Bode Plot
- Fixed several bugs
- Incorrect zoom trace in Roll mode (Stop)
- Bode Plot draw error (missing draw)
- Bode Plot zig-zag phase
- [Measure] Gating settings cannot be typed in
SDS2000X Series Firmware Update
Version:
V1.2.2.2R19
SDS1000DL+ Series Firmware update
Version:
V6.02.01.13
SDS2000X Plus Series Firmware Update
Version:
V1.3.9R12
SDS5000X Series Firmware Update
Version:
V0.9.5R3
SDS1000CML+ Series Firmware Update
Version:
V6.01.01.22
SLA1016(Optional) Firmware Update
Version:
V7.8.1.8
SDS2000X Series Firmware Update
Version:
V1.2.2.2R15
SDS6000 Firmware Update
Version:
V1.4.9.3
2024-04-23
Release notes
1. Supported new probes: Siglent’s SCP5030, SCP5030A, SCP5150, SCP5500 and LeCroy’s CP150, HVD3106A
2. Option to hide Memory and Math traces
3. Webserver: Screenshot can be directly copied and pasted
4. Fixed several bugs
a) Decode Threshold bug
b) NO persistence available with frames captured by SEQUENCE
2. Option to hide Memory and Math traces
3. Webserver: Screenshot can be directly copied and pasted
4. Fixed several bugs
a) Decode Threshold bug
b) NO persistence available with frames captured by SEQUENCE
SDS2000X-E Series Firmware Update
Version:
V1.1.20R6
SDS2000X Plus Series Firmware Update
Version:
V1.3.9R10
2022-03-29
Release notes
Compatible with new hardware (hardware version: 04-xx).
Note:
Note:
- This is a firmware compatible with new hardware. No feature or specification difference between it and 1.3.9R6. It’s not necessary to upgrade it from 1.3.9R6 to this release.
- This release cannot be downgraded to former releases.
SDS1000DL+ Series Firmware update
Version:
V6.02.01.11
SDS5000X Series Firmware Update
Version:
V0.9.5R2
2021-05-25
Release notes
Fixed a bug which may cause failure on installation of option key in 0.9.5R1.
0.9.5R1 revision history:
1. Expanded the post-trigger range from 5,000 to 10,000 divisions
2. Measurement:
a) Supported cursors for measurement
b) Supported Track plot
3. Display:
a) Supported to show bandwidth information on the channel descriptor box
b) Supported to display axis label
4. Save/Recall: a) Supported to Print only grid area b) Supported to save FFT result
5. DVM: Supported limit beeper
6. Updated Russian menu
7. Fixed several bugs
a) Last Save/Recall path is not remembered
8. Measurement invalid in Roll when acquisition stops and Zoom is enabled
0.9.5R1 revision history:
1. Expanded the post-trigger range from 5,000 to 10,000 divisions
2. Measurement:
a) Supported cursors for measurement
b) Supported Track plot
3. Display:
a) Supported to show bandwidth information on the channel descriptor box
b) Supported to display axis label
4. Save/Recall: a) Supported to Print only grid area b) Supported to save FFT result
5. DVM: Supported limit beeper
6. Updated Russian menu
7. Fixed several bugs
a) Last Save/Recall path is not remembered
8. Measurement invalid in Roll when acquisition stops and Zoom is enabled
SDS5000X Series Firmware Update
Version:
V0.9.3R3
2020-09-29
Release notes
- Expanded the offset range
- New serial protocols supported (optional):
- SENT, trigger & decode
- Manchester, decode only
- Measurement enhancement:
- Supported user-defined thresholds (Upper, Middle and Lower): Measure | Config | Threshold
- Added items: +Area@AC, -Area@AC, Area@AC, AbsArea@AC
- Math:
- Added new operator – Interpolate
- Added function expression information to the math descriptor box
- Display:
- Supported selectable color for traces: Display | Color Setting
- Supported floating menu so that the waveform is not compressed horizontally when the right-side menu is displayed: Display | Menu Style
- Supported to hide analog traces
- Save/Recall:
- Added option “Save all channel” for csv file
- Supported to save math traces (except FFT)
- Supported serial trigger as source of the frequency counter
- Supported LeCroy probes ZD1000/ZD1500 with LPA10 probe adapter; supported Tek TekProbe interface level II probes with TPA10 probe adapter
SDS1000CML+ Series Firmware Update
Version:
V6.01.01.21R2
SDS2000X Series Firmware Update
Version:
V1.2.2.2R10
SDS1xx2X-E Firmware Update
Version:
V1.3.17R1
SDS1000CFL_2CH Firmware Update
Version:
V5.08.02.38
SDS6000 Firmware Update
Version:
V1.4.8.3
SDS2000X-E Series Firmware Update
Version:
V1.1.20R3
SDS2000X Plus Series Firmware Update
Version:
V1.3.9R6
SDS5000X Series Firmware Update
Version:
V0.9.1B2
SDS1000DL+ Series Firmware Update
Version:
V6.02.01.10R2
SDS2000X Series Firmware Update
Version:
V1.2.2.2
SDS1xx4X-E Firmware Update
Version:
V6.1.20R1
SDS1000X Series Firmware Update
Version:
V1.1.1.2.15R10
SDS1000CFL_4CH Firmware Update
Version:
V5.03.02.38
SDS6000A Firmware Update
Version:
V1.4.5.2
2023-04-25
Release notes
1.Eye Diagram: supported 100Base-T1 (PAM3)
2.SCPI: Supported Search
3.Supported USB-GPIB
4.Fixed several bugs
2.SCPI: Supported Search
3.Supported USB-GPIB
4.Fixed several bugs
- DY-WTFK-202203165613:Spectrum menu after installing
- DY-WTFK-202209237014: Scope restarts acquisition after few seconds when stopped
- DY-WTFK-202207076348: Filter settings way off in special acquisition modes
- DY-WTFK-202209237015: Zone trigger doesn’t work at some input frequencies
SDS2000X Plus Series Firmware Update
Version:
V1.3.9R4
2021-09-06
Release notes
- Measurement enhancement:
- Supported cursors for measurement
- Supported Track plot
- Added parameters: Positive Slope and Negative Slope
- Display:
- Supported to display axis label
- Auto hide menu setting increased to 10 seconds
- Added “Hide” button in the fast menu of channel for quickly hiding trace
- Save/Recall:
- Supported network storage
- Supported to Print only grid area
- Supported to save FFT result
- Updated the File Manager
- Bode Plot:
- The maximum generator amplitude changed from 6Vp-p to 24Vp-p
- Supported single sweep
- Horizontal: Time Zero strategy updated – time zero changed from center display to trigger position.
- Acquisition: Deleted some unnecessary clear operations on the history buffer
- Updated Russian menu
- Supported setting Cursors by virtual keypad
- Fixed several bugs
- Decode failure occurs on last nibble or byte
- The “STL?” query issue in AWG function
- If persistence is enabled, and you change the trigger setting, persistence will be switched off
- Decode list can't go higher than item #2
- Decode format is reset to "binary" when recalling stored settings
- Sequence capture does not work with serial trigger from digital channel
- ERES 0.5-bit works for ERES(C1), but not for ERES(F1)
- The icons for rise and fall time in the Measure Select screen are reversed
- When switching the attenuator, the message “Zone is too small” appears
- After shutting-down the scope and rebooting not all settings are restored
- Bode plot abnormal when Sequence is enabled
- SENT decode: tolerance not functional
- SENT decode: only display CRC segment but no calculation on the
- CRC checksum
- SENT decode: The Short Serial data is NOT decoded if only 16 frames are sent. If a 17th frame follows, the data is decoded
- SENT decode: Changing the horizontal time/div affects the ability to decode.
- Save/recall: Number of digits of time stamp is not enough in the long period
- Infinite persistence not works after switching between 8-bit and 10-bit
- Tolerance of UART decode too strict
- FFT max. scale is unrealistic
SDS2000X-E Series Firmware Update
Version:
V1.1.19R5
2020-07-03
Release notes
1. Added support for the SAG1021I USB Isolated AWG Module Hardware
2. Fixed the bug: Sometimes PNSU command returns invalid value (Need referring to the latest Program Guide)
3. Added 9 data bits for UART decoding
4. Fixed the bug of UART decoder with some special settings
5. Increased baud rate of UART trigger from 5 Mbps to 20 Mbps
6. Fixed the bug: The command ‘WF? DAT2’returns error length of waveform when digital is enable
7. Fixed the bug: CSV file of waveform has no indication of the trigger point in the data
8. Fixed the bug: After repowering all FFT markers are on just one peak
9. Fixed the bug: After repowering, signal level of CAN trigger can't be recalled
10. Fixed a few SCPI Commands errors:
MATH: CURSOR_VALUE?
C3:INVERT_SET? is missing
HISTORY_LIST? is missing
DIGITAL:LOW8_SWICHT, typo in name
C5:COUPLING? typo in name
11. Fixed the Bode Plot bug: Sometime there isn't enough delay after the scope switches timebase values before it tries to take a measurement
12. Fixed the bug: Matlab can’ t import 14 M Matlab waveform files
13. Fixed the bug:‘WF?’ command ignores the length set by ‘WFSU’ for digital
2. Fixed the bug: Sometimes PNSU command returns invalid value (Need referring to the latest Program Guide)
3. Added 9 data bits for UART decoding
4. Fixed the bug of UART decoder with some special settings
5. Increased baud rate of UART trigger from 5 Mbps to 20 Mbps
6. Fixed the bug: The command ‘WF? DAT2’returns error length of waveform when digital is enable
7. Fixed the bug: CSV file of waveform has no indication of the trigger point in the data
8. Fixed the bug: After repowering all FFT markers are on just one peak
9. Fixed the bug: After repowering, signal level of CAN trigger can't be recalled
10. Fixed a few SCPI Commands errors:
MATH: CURSOR_VALUE?
C3:INVERT_SET? is missing
HISTORY_LIST? is missing
DIGITAL:LOW8_SWICHT, typo in name
C5:COUPLING? typo in name
11. Fixed the Bode Plot bug: Sometime there isn't enough delay after the scope switches timebase values before it tries to take a measurement
12. Fixed the bug: Matlab can’ t import 14 M Matlab waveform files
13. Fixed the bug:‘WF?’ command ignores the length set by ‘WFSU’ for digital
SDS1xx4X-E Firmware Update
Version:
V6.1.12
SDS1000X Series Firmware Update
Version:
V1.1.1.2.15R3
SDS1000DL+ Series Firmware Update
Version:
V6.02.01.08
SDS6000A Firmware Update
Version:
V1.4.4.1
2023-02-08
Release notes
1. Force trigger strategy changed (same as SDS2000X HD)
2. Save/Recall
a) Supported to save all sequence segments
b) Supported Auto Save
3. Fixed several bugs
a) Cannot communicate with the SDG2000X and SDG7000A over USB in Bode Plot
b) Random +/-200 ps skew between channels after power/reboot cycle
c) [Power analysis] - Switching losses - Error in calculations
d) FFT wrong vertical scale
e) Memory channel trace always on top
2. Save/Recall
a) Supported to save all sequence segments
b) Supported Auto Save
3. Fixed several bugs
a) Cannot communicate with the SDG2000X and SDG7000A over USB in Bode Plot
b) Random +/-200 ps skew between channels after power/reboot cycle
c) [Power analysis] - Switching losses - Error in calculations
d) FFT wrong vertical scale
e) Memory channel trace always on top
SDS2000X Plus Series Firmware Update
Version:
V1.3.7R5
2020-11-12
Release notes
- New serial protocols supported (optional):
- SENT, trigger & decode
- Manchester, decode only
- Measurement enhancement:
- Supported user-defined thresholds (Upper, Middle and Lower): Measure | Config | Threshold
- Added items: +Area@AC, -Area@AC, Area@AC, AbsArea@AC
- Math: added new operator – Interpolate
- Display:
- Supported selectable color for traces: Display | Color Setting
- Supported floating menu so that the waveform is not compressed horizontally when the right-side menu is displayed: Display | Menu Style
- Supported to show bandwidth information on the channel descriptor box
- Save/Recall:
- Added option “Save all channel” for csv file
- Supported to save math traces (except FFT)
- Bode Plot:
- Optimized scan speed
- Fixed unexpected glitch issue
- Supported serial trigger as source of the frequency counter
- Unlocked zoom in stop mode for Roll
- Supported trigger Default or AutoSetup operations by pressing corresponding button twice
- Fixed several bugs
- Some vertical measurement error in roll mode
- Missed peak marker in FFT two-tone test
- AWG problem of importing the arb file from a U-disk
- Whenever the screen is touched, the pass/fail statistics is reset to zero
- SPI data value setting issue using virtual keypad
- Compatibility issue between WebServer and latest Chrome/Edge browsers
SDS5000X Series Firmware update
Version:
V0.8.7R1B1
SDS2000X-E Series Firmware Update
Version:
V1.1.19R2
SDS1000X-E Series Firmware Update
Version:
V5.1.3.13
SDS1000X Series Firmware Update
Version:
V1.1.1.2.15
SDS1000DL+ Series Firmware Update
Version:
V6.02.01.07
SDS1000CML+ Series Firmware Update
Version:
V5.01.02.32
SDS6000A Firmware Update
Version:
V1.4.3.3
2022-06-28
Release notes
Note: This release cannot be downgraded to former releases.
- Math: added filter operator
- Supported to save waveform as Memory traces, which store the raw data instead of the screen data (as Ref does), and can be source of Measure/Math etc.
- Measure: improved the AIM limit from 1,000 to up to 65,000 (AIM limit: the upper limit of horizontal parameters measure statistics in one frame )
- Optimized intensity display of math traces.
- Added support for mouse wheel when using a mouse
- Supported CP030 current probe (with LPA10 adapter)
- Eye Diagram: 100Base-TX signal supported
- Trigger: Pattern trigger strategy changed
- Power Analysis:
- Supported MOSFET SOA (Safe Operating Area)
- Bigger table size
- Fixed several bugs
- Moving the traces by gestures may cause the scope to freeze
- [Bode Plot]Vertical Ref.level manual setting is partially bad
- [Measure]Track plot - not working well in general
- [Power Analysis]Current harmonics forgets table/bar view
- Waveform Capture Rate breakdown at 20 ns/div
- Measurements skip buffers in history mode
SDS2000X Plus Series Firmware Update
Version:
V1.3.5R5
2020-05-18
Release notes
1. Supported to hide analog traces
2. Added function expression information to the math box
3. Optimized AWG DC output accuracy at +/-3V
4. Frequency counter supported to count serial trigger events
5. Fixed several bugs
a) Incorrect cursor horizontal label for FFT traces
b) 2-channel 100MHz model cannot be upgraded to 350MHz
c) FRFR measure invalid from Roll to Stop
d) Unexpected behaviors when probe attenuation factor is not 1x
e) Some bugs in PA
2. Added function expression information to the math box
3. Optimized AWG DC output accuracy at +/-3V
4. Frequency counter supported to count serial trigger events
5. Fixed several bugs
a) Incorrect cursor horizontal label for FFT traces
b) 2-channel 100MHz model cannot be upgraded to 350MHz
c) FRFR measure invalid from Roll to Stop
d) Unexpected behaviors when probe attenuation factor is not 1x
e) Some bugs in PA
SLA1016 Firmware
Version:
V8.1.16
SDS5000X Series Firmware Update
Version:
V0.8.2R1
SDS6000A Firmware Update
Version:
V1.4.0.0
SDS2000X Plus Series Firmware Update
Version:
V1.3.5R10
SDS5000X Series Firmware Update
Version:
V0.8.0R1B5
SDS2000X-E Series Firmware Update
Version:
V1.1.17R6
SDS3000X HD Firmware Update
Version:
V1.0.3.3
SDS6000L Firmware Update
Version:
V1.0.7.8
2024-04-02
Release notes
1. Fixed several bugs
a) Cannot exit from Bode plot in some case
b) Cannot detect active probes correctly when the probes are connected at power-on
c) “Set to 50% level” takes the scope frozen in some case
d) Sample rate is displayed incorrectly after reboot from Fixed Memory Length mode
a) Cannot exit from Bode plot in some case
b) Cannot detect active probes correctly when the probes are connected at power-on
c) “Set to 50% level” takes the scope frozen in some case
d) Sample rate is displayed incorrectly after reboot from Fixed Memory Length mode
SDS6000L Firmware Update
Version:
V1.0.6.3
SDS7000A Firmware Update
Version:
V1.1.5.1
SDS7000A Firmware Update
Version:
V1.1.4.2
2024-03-12
Release notes
- Supported new probes: Siglent’s SCP5030, SCP5030A, SCP5150, SCP5500
- Measure: Optimized UX of Track and Trend; Supported to export measure data
- Fixed several bugs
- Slow response after pressing Math button
- AWG: SCPI cannot set Load
- Some bugs of USB2.0 compliance test
- Some bugs of 100Base-TX and 1000Base-T compliance test
- Some bugs on Options’ unlock
SDS800X HD Firmware Update
Version:
V1.1.3.3
SLA1016(Optional) Firmware Update
Version:
V8.2.3
SDS2000X HD Series Firmware Update
Version:
V1.2.2.5
SDS6000L Firmware Update
Version:
V1.0.5.3
2023-03-30
Release notes
Revision Record
1.The first release
Upgrade Instructions
Upgrade from the Web Server
A built-in web server provides an approach to control the instrument by web browser. This process doesn’t require any additional software to be installed on the controlling computer. Set the LAN port correctly (see the User Manual for details), input the IP address of the instrument in the browser address bar, and then the user can browse and control the instrument on the web.
WARNING: DO NOT shut off the instrument until the update is completed.
Click the “FirmwareUpdate” button in the web interface
Select the correct update file (*.ads) stored on the computer. The instrument will automatically download the update file and perform the upgrade once the file is specified.
WARNING: DO NOT shut off the instrument until the update is completed.
Upgrade from a U-disk (USB Memory device)
WARNING: DO NOT shut off the instrument until the update is completed.
Note: If your firmware version is less than V1.0.5.3, you need to perform twice the V1.0.5.3 upgrade
Copy the update file (*.ads) to a FLASH type U-disk, and then insert the U-disk into one of the USB host ports of the instrument.
Click on the Utility on the instrument control screen, and press "Maintenance -> Upgrade". The following the menu should pop up and allow you to select the upgrade file
Click Browse in the menu above, and then select the correct update file (*.ads) in the pop-up resource manager
Click the recall icon in the interface above and return to the upgrade dialog. Click Upgrade to perform the upgrade operation:
The system will first copy and verify the upgrade package. After the upgrade package is validated, the following interface will appear. Click Reboot to continue the upgrade, or click Cancel to cancel it.
After the instrument reboots, check the version number through the Utility->System Info to confirm if the upgrade is successful.
WARNING: DO NOT shut off the instrument until the update is completed.
1.The first release
Upgrade Instructions
Upgrade from the Web Server
A built-in web server provides an approach to control the instrument by web browser. This process doesn’t require any additional software to be installed on the controlling computer. Set the LAN port correctly (see the User Manual for details), input the IP address of the instrument in the browser address bar, and then the user can browse and control the instrument on the web.
WARNING: DO NOT shut off the instrument until the update is completed.
Click the “FirmwareUpdate” button in the web interface
Select the correct update file (*.ads) stored on the computer. The instrument will automatically download the update file and perform the upgrade once the file is specified.
WARNING: DO NOT shut off the instrument until the update is completed.
Upgrade from a U-disk (USB Memory device)
WARNING: DO NOT shut off the instrument until the update is completed.
Note: If your firmware version is less than V1.0.5.3, you need to perform twice the V1.0.5.3 upgrade
Copy the update file (*.ads) to a FLASH type U-disk, and then insert the U-disk into one of the USB host ports of the instrument.
Click on the Utility on the instrument control screen, and press "Maintenance -> Upgrade". The following the menu should pop up and allow you to select the upgrade file
Click Browse in the menu above, and then select the correct update file (*.ads) in the pop-up resource manager
Click the recall icon in the interface above and return to the upgrade dialog. Click Upgrade to perform the upgrade operation:
The system will first copy and verify the upgrade package. After the upgrade package is validated, the following interface will appear. Click Reboot to continue the upgrade, or click Cancel to cancel it.
After the instrument reboots, check the version number through the Utility->System Info to confirm if the upgrade is successful.
WARNING: DO NOT shut off the instrument until the update is completed.
SDS2000X HD Series Firmware Update
Version:
V1.2.1.1
SDS6000A Firmware Update
Version:
V1.3.9.0
SDS1104X-U Firmware Update
Version:
V1.1.5R6
SDS2000X Plus Series Firmware Update
Version:
V1.3.5R3
Release Notes
Release Notes